IP5189T Power Bank Troubleshooting and Repair Guide

Explore our detailed guide on troubleshooting and repairing the IP5189T Power Bank. Get practical tips to restore your device's functionality.

This guide will address 10 common issues encountered with the IP5189T-based power bank circuit (e.g., Model Y65) and provide step-by-step solutions.

1. Power Bank Not Turning On

Problem:
The power bank does not respond when the button is pressed.
No indicator LEDs light up.

Possible Causes:
Faulty push button.
IP5189T IC malfunction.
Battery connection issue.

Solution:
Inspect the push button for mechanical damage; replace it if necessary.
Check the battery voltage using a multimeter. It should be above 3.0V. Recharge or replace the battery if needed.
Verify that the IP5189T IC receives power (check VCC pin). Replace the IC if no issues are found with the battery or connections.
China Power Bank Repair

2. No Charging When Connected to Input Power

Problem:
The power bank doesn't charge when connected to a 5V input via Type-B or Type-C.
Indicator LEDs do not light up.

Possible Causes:
Damaged input connector or loose solder joint.
Faulty charging cable or adapter.
Short circuit in the input section.
IP5189T input pins malfunction.

Solution:
Inspect and resell the Type-B and Type-C connectors.
Test with a different adapter and cable.
Check for short circuits near the input section (diodes, capacitors, MOSFETs). Replace any damaged components.
Measure voltage at the input pins of the IP5189T. If the IC is not working correctly, replace it.

3. Power Bank Overheating

Problem:
Excessive heat during charging or discharging.

Possible Causes:
Faulty NTC resistor (thermistor).
Short circuit in the charging or discharging circuit.
The high internal resistance of the battery.

Solution:
Test the NTC resistor with a multimeter; replace if damaged.
Check for shorted MOSFETs or capacitors in the boost converter section.
Inspect the battery for swelling or damage; replace it if necessary.

4. No Output from USB Ports

Problem:
No 5V output at either USB-A port.
The device does not charge.

Possible Causes:
Faulty output MOSFET or inductor in the boost converter.
Damage to the USB output connector.
IP5189T IC not boosting the voltage.

Solution:
Measure the voltage across the inductor. If it's absent, replace the MOSFET or inductor.
Check and resell the USB output connectors.
Test the boost converter functionality by measuring the voltage on the output pins of the IP5189T IC. Replace the IC if faulty.

5. Uneven or Incorrect LED Indicators

Problem:
LEDs show incorrect battery percentage.
LEDs remain stuck in one state.

Possible Causes:
Faulty LED driver pins in the IP5189T.
Damaged LEDs or resistors.

Solution:
Test the LEDs and associated resistors. Replace damaged components.
If the LED driver pins of the IP5189T are non-functional, replace the IC.

6. Power Bank Charges Devices Slowly

Problem:
Output current is lower than expected.
Charging time for connected devices is abnormally high.

Possible Causes:
Low-quality or damaged output capacitors.
Faulty MOSFETs or inductors in the boost circuit.
IP5189T IC is unable to deliver sufficient current.

Solution:
Inspect and replace output capacitors with proper-rated ones.
Test and replace the MOSFETs and inductors.
Replace the IP5189T if the issue persists.

7. Power Bank Not Fully Charging

Problem:
Battery charge stops at a lower percentage (e.g., 50% or 75%).

Possible Causes:
Battery health deteriorated.
Faulty NTC resistor providing incorrect readings.
IP5189T IC limiting charge cycle.

Solution:
Measure the battery voltage. If below the expected capacity, replace the battery.
Test the NTC resistor; replace it if damaged.
Replace the IP5189T IC if it fails to charge fully despite proper input.

8. USB Output Ports Short-Circuit

Problem:
The power bank shuts down when a device is connected.
No output voltage on USB ports.

Possible Causes:
Damaged USB port.
Shorted diodes or capacitors.

Solution:
Inspect and resell the USB port or replace it if damaged.
Check diodes and capacitors near the USB ports; replace shorted components.

9. Power Bank Automatically Turns Off

Problem:
The power bank turns off prematurely, even with sufficient battery charge.

Possible Causes:
Faulty battery connection or degraded battery.
Over-sensitive overcurrent protection in IP5189T.

Solution:
Verify the battery connections and measure their voltage. Replace if degraded.
Inspect the IC protection circuit components; replace the IP5189T if necessary.

10. Indicator LEDs Blink Continuously

Problem:
LEDs blink but do not stabilize, even with proper charging.

Possible Causes:
IP5189T malfunction.
Input voltage fluctuating or insufficient.

Solution:
Test the input voltage stability using a multimeter. Ensure the adapter delivers a steady 5V.
Replace the IP5189T if no other issue is identified.

Previous Post Next Post